Desktop Gantry Fiber Laser Cleaning Machine for Molds and Rotary Parts – 100-300W, 0.02mm Repeatability
A compact gantry with 400 mm X and Z travel on linear guides and a ball screw, repeating to 0.02 mm. A self-centring three-jaw chuck and 0-60 rpm rotary axis carry 50 kg; the JPT source comes in 100, 200 or 300 W over a 10 m fiber, 10-100 mm wide, 2-6 m2/h on medium rust.

0.05 mm positioning accuracy, 0.02 mm repeatability, and a servo rotary axis supporting 50 kg loads.
JPT pulsed laser with 2–10 mJ pulse energy and 20–200 kHz frequency. Cleaning speed reaches 2–6 m²/h at 200 W.
Light curtain, area scanner, interlock and E-stop. PLC touchscreen control with USB, Ethernet and Robot I/O connectivity.
The head rides an X/Z gantry with 400 mm of travel on each axis, on linear guides and a ball screw, holding 0.05 mm positioning and 0.02 mm repeat. On the table a self-centring three-jaw chuck and a 0-60 rpm servo rotary axis index to 0.1 degree and carry 50 kg, so a shaft, tube or flange turns a full revolution in one clamping. The JPT pulsed source comes in 100, 200 or 300 W, 2-10 mJ per pulse, 10-500 ns and 20-200 kHz, over a 10 m fiber, 10-100 mm wide, running 2-6 m2/h on medium rust at 200 W. A PLC with a 10-inch touch panel stores programs and parameters, with USB, Ethernet, Robot I/O and a safety interlock; the work zone is Class 4, guarded by light curtain, area scanner, interlock and E-stop, at 70 dB(A) or less on single-phase 220 V and 2.2 kW.
| Parameter | Specification |
| 01 LASER SYSTEM | |
| Laser type | Pulse fiber laser (JPT) |
| Laser power | 100 W / 200 W / 300 W |
| Single-pulse energy | 2-10 mJ |
| Pulse width | 10-500 ns adjustable |
| Repetition frequency | 20-200 kHz operating range |
| Cooling | Integrated water cooling |
| Fiber delivery | 10 m |
| Cleaning width | 10-100 mm adjustable |
| Cleaning efficiency | 2-6 m2/h @ 200 W, medium rust |
| 02 MOTION & ROTARY AXIS | |
| X-axis travel | 400 mm |
| Z-axis travel | 400 mm |
| Positioning accuracy | ±0.05 mm |
| Repeat positioning accuracy | ±0.02 mm |
| Rotary axis | 0-60 rpm servo |
| Indexing accuracy | ±0.1 deg |
| Maximum load | 50 kg |
| 03 ELECTRICAL & CONTROL | |
| Power supply | 220 V, 50/60 Hz, single phase |
| Total power | 2.2 kW at 200 W configuration |
| Control system | PLC + 10-inch touch HMI |
| Interfaces | USB / Ethernet / Robot I/O / Safety interlock |
| Air supply | 0.4-0.6 MPa for pneumatic options |
| 04 ENVIRONMENT & SAFETY | |
| Noise | 70 dB(A) or less |
| Operating temperature | 5-40 C |
| Operating humidity | Below 70% |
| Laser safety | Class 4 work zone, external guarding required |
| Safety protection | Light curtain / area scanner / interlock / E-stop |

The controller board is what makes it seamless
The blue board is the main controller, with four connectors and double-row terminals crimped in one piece. It streams the path across a whole panel without stopping to stitch, and the cleaning area is set in the program, so the surface carries no stitch marks.
Servo and linear module: smooth travel, even energy
A servo motor and linear module sit in the column, on traceable branded guides and carriages. How smoothly the axis runs decides whether the scan speed stays constant, and constant speed is what keeps energy per area even, so the surface never comes out patchy.


JPT source, dual red positioning, quartz field lens
Under the red housing sit the JPT source and a quartz field lens, with two red beams meeting on the workpiece so the spot is visible at a glance. Seeing where it lands is what makes thin and coated parts safe to clean, and the quartz lens holds its power over long runs.
One-touch stop: thin parts fail on one extra second
A column of red buttons on the panel, the top one an emergency stop that cuts the beam and stops the machine at a touch. Thin sheet, plating and precision parts fail on one extra second, and when the hand is faster than the program this is the last line of defence.

Materials and process fit
| Material | Job | How | Note |
| Carbon steel / cast iron | Hulls, structures, castings | 200-300 W, long pulse lifts heavy rust | 2-6 m2/h |
| Stainless steel | Weld tint and heat colour | 200 W, short pulse, surface tint only | Weld profile intact |
| Aluminium | Oxide film, oil, weld prep | 100-200 W, low density, two passes | Never cut through in one |
| Copper / reflective | Oxide and pre-weld clean | Low power, high frequency, fast scan | Watch peak density |
| Shafts / tubes | Outer diameter rust and paint | Chuck plus A-axis turn, Z step-over | No seam |
| Moulds | Cavity carbon and release agent | 200 W with rotary or angle fixture | Texture kept |
| Cutters / gears | Edges and tooth faces | Low power, short pulse | Surface layer only |
Laser Cleaning Samples
Related Products
Send us an email to get further information you need, including our latest price, the best-customized solution, or any problem with the existing machine.






















